You are here: Home > Sensors and IMUs
Sort By:
Page of 1  
Breakout Board MPXV5004DP
Our Price: $18.90

Differential Pressure Sensor board.
Data Sheet
Breakout Board LISY300 GYRO 300deg/sec
Our Price: $24.95

ST Microelectronics LISY300AL break out board with an output rate of 300 degrees/second. The smallest board in the market and includes low pass filter.
Breakout Board Expandable IMU ADXL330/LISY300 v2
Our Price: $44.95

Amazing combo IMU! So small that the dust over it looks huge in the pictures. Can be transformed into 4,5 and 6 degrees of freedom by just soldering two extra LISY300 Breakout board gyros that can be located here. Designed to be easily adapted into any system.


Information:
-ADXL330
-LISY300AL
Pitot Tube- Static and Dynamic Probe Set
Our Price: $5.95

This is a double nice pitot tube set used to measure the airspeed. Can be use in ArduPilot Shield and MPXV5004DP Breakout Board.

It includes the static and dynamic pressure probes.
Breakout Board for FreeScale Pressure Sensors
Our Price: $3.90

Low pass filtered breakout board for Freescale pressure sensors. Easy to interface! The pins are labeled as: Analog, +5V and Ground.
AttoPilot XYZ Horizon Sensor
Price: $114.60

Custom version of Attopilot horizon sensors. These sensors are used to know the orientation of the aircraft with respect to the ground. -Comes with FMA compatible connectors (not soldered, in case you want to use something else).
-Compatible with ArduPilot and Range Video OSD.
-The OP-AMP gain is set to 1000x (1Mohms/1kohms).
Kit MPXV5004DP
Our Price: $20.90

This is a stand-alone airspeed sensor. Includes Pitot Tube and Servo Cable.

Data Sheet
ArduIMU+ Board
Our Price: $29.90

[Note: this is the V1 board only, with no sensors. If you want the ArduIMU+ V2 board, it's here. ]

This hardware has dual power regulator (3.3v and 5v), GPS port, an Atmega328@16mhz and a lot of status LED's. All this just to give the funnest and cheapest IMU-AHRS on the market! Includes the pin headers.


-Code
Thermopile MLX90247
Our Price: $12.90

NOTE: If you buy six units i will give you a good discount. ;-)

 

Solid state thermopile sensor
On-chip thermistor for ambient temperature compensation
High reliability and long-term stability
 
ArduIMU+ V2 (Flat)
Our Price: $99.90

This hardware consists of a 3 axis accelerometer and 3 gyroscope, dual power regulator (3.3v and 5v), GPS port, an Atmega328@16mhz and a lot of status LEDs. It's the cheapest IMU-AHRS on the market!
Triple Axis Gyro 300°/s LPX530AL Board
Our Price: $44.99

This is a triple axis ST MEMS gyroscope board, it has one  LPR530AL for Pitch and Roll and one LPY530AL  for Yaw. Capable to measure the angular velocity with a full scale of 300°/s. Three different analog outputs are provided for the x- , y- axes and z - axes - one 1x amplified and the other 4x amplified. This boards is designed with a removable edges, in case you don't want to screw the board to your project you can just easily break them away to keep the minimal size!
HMC5843 - Triple Axis Magnetometer
Our Price: $49.90

This is a 3-axis digital compass board based on the Honeywell's HMC5843. Communication with the HMC5843 is done through an I2C interface. The board has an I2C translator and 3.3V power regulator that will easily let you use it with 3.3V and 5V applications using a solder jumper.

This magnetometer can be used on our ArduIMU+ and ArduPilotMega Shield or any microcontroller.