You are here: Home > ArduPilot
Sort By:
Page of 1  
ArduPilot Shield V2
Base Price: $36.00

Ardupilot Shield!
ArduPilot Shield IR Cable 30cm
Base Price: $7.50

This is the official custom made Infrared cable for ArduPilot Shield (FMA compatible).

Available in two flavors: 30cm and 60cm long!

Do you need the other end connector header? Click here.
Pitot Tube- Static and Dynamic Probe Set
Our Price: $5.95

This is a double nice pitot tube set used to measure the airspeed. Can be use in ArduPilot Shield and MPXV5004DP Breakout Board.

It includes the static and dynamic pressure probes.
ArduPilot Shield V2 Kit
Our Price: $48.90

Complete ArduPilot Shield Kit!!
Official Ardupilot FTDI Cable
Our Price: $19.90

This a practical and easy to use FTDI cable. If you look carefully into your ardupilot board you will see the labels "BLK" (black) and "GRN" (green), those colors indicate the polarity of this cable. All the FTDI stuff is inside the USB connector, making it look like a regular USB cable.

Note: The TX/RX signals are 3.3volts, making it even more flexible, the power supply is 5volts (red wire).

 
AttoPilot XYZ Horizon Sensor
Price: $114.60

Custom version of Attopilot horizon sensors. These sensors are used to know the orientation of the aircraft with respect to the ground. -Comes with FMA compatible connectors (not soldered, in case you want to use something else).
-Compatible with ArduPilot and Range Video OSD.
-The OP-AMP gain is set to 1000x (1Mohms/1kohms).
Connector Header for FMA/AttoPilot XYZ sensors
Our Price: $2.90

This header matches the FMA Co-Pilot connectors. Includes six terminals (two extra!). Ideal for building your own connector.
ArduStation
Our Price: $47.50

New Portable Open-Source ArduPilot Ground Station (Arduino and Xbee Based)
ArduPilot Shield v2 (No 3.3V Regulator & Sensor)
Our Price: $20.00

Ardupilot Shield V2 Economic version (with no 3.3V Power regulator).
ATmega328p with Arduino Bootloader
Our Price: $5.50

Atmel's ATMega328 8-Bit Processor in 28 pin DIP package. It's like the ATmega168, with double the flash space. 32K of program space. 23 I/O lines, 6 of which are channels for the 10-bit ADC. Runs up to 20MHz with external crystal. Package can be programmed in circuit. 1.8V to 5V operating voltage.
Connector Header Female LOCKED RA 5POS
Our Price: $2.90

Connector header used on the ArduPilot Shield to connect the Infrared sensors using this special cable.
HMC5843 - Triple Axis Magnetometer
Our Price: $49.90

This is a 3-axis digital compass board based on the Honeywell's HMC5843. Communication with the HMC5843 is done through an I2C interface. The board has an I2C translator and 3.3V power regulator that will easily let you use it with 3.3V and 5V applications using a solder jumper.

This magnetometer can be used on our ArduIMU+ and ArduPilotMega Shield or any microcontroller.
ArduIMU+ Board
Our Price: $29.90

[Note: this is the V1 board only, with no sensors. If you want the ArduIMU+ V2 board, it's here. ]

This hardware has dual power regulator (3.3v and 5v), GPS port, an Atmega328@16mhz and a lot of status LED's. All this just to give the funnest and cheapest IMU-AHRS on the market! Includes the pin headers.


-Code